Equip
Flat panel steun
650201
Equip 650201 Handleiding
Hier is de Equip 650201 (Flat panel steun) gebruikershandleiding. 2 pagina's in taal Engels met een gewicht van 2.0 Mb. Als u geen antwoorden op uw probleem kunt vinden Vraag het onze community.
Pagina 1/2
LCD TV WALL MOUNT BRACKET
TILTING
Universal | 650201
Features
l Supports 58 ~ 94cm (23” ~ 37”) Flat Panel Display
l Distance from TV to Wall: 46mm
l Flexible Adjustment with 0º ~ -10º Tilt
l VESA Mount Standards: Maximum 400 x 200mm
l Hole Pattern: Maximum 420mm Wide and 230mm High
l Universal Mounting Pattern
l Bubble Level Integrated
l Load Capacity: Maximum 75kg (165lbs)
WARNING!
Make sure that any listed parts are not missing or defective. Improper installation would result in personal
injury or damage to equipment. If you have any questions about installation, please visit
http://www.equip-info.net for more assistance.
Hardware Kit
Note: Any of the hardware in kit will be required. Other joint parts are forbidden.
INSTALLATION
Mount Wall Plate on the Wall - The product is designed for mounting on solid brick, concrete or hard wood
batten/studs wall, but plasterboard or paneled wall is not allowed.
(a) Solid Brick, Concrete Block Wall - Use the wall plate○
a as a template to mark 6 holes location on the
wall, three in the top row slots and three more in the bottom row. Make sure these holes are level and there
is at least 200mm between any two holes. Drill these holes with a 10mm masonry bit to at least 60mm in
depth. Insert a concrete anchor○
e into each of these holes. Attach the wall plate to the wall using 6 lag
bolts○
d and 6 lag bolt washers○
g.
(b) Hard Wood Batten/Stud Wall - The wall plate○
a must be mounted to two wood studs. Use a high
quality stud sensor to locate three adjacent studs. It is a good idea to verify where the studs are located
with an awl or thin nail shown in diagram 1-A. Drill a 3mm deep hole at the desired height in each stud using
a 4mm drill bit. Use the wall plate○
a as a template to mark the location of the second hole in each stud.
Pre-drill these holes using the 4mm drill bit as well. Attach the wall plate to the wall using the 4 lag bolts○
d
and 4 lag bolt washers○
g. Make sure the wall plate is oriented so the flat surface in the center of the plate in
against the wall shown in diagram 1-B. Note: Do not use any concrete ancher when you mount the bracket
onto hard wood wall.
Mount the TV Rails on the Back of Your Display and Install - Make sure the two TV rails○
b are
mounted at an equal distance from the top of the TV and as close to the center as possible as shown in
diagram 2-A. Knobs should face the outside of the television. Plastic spacers○
h are provided to be used
with M4, M5, M6 and M8 mount screws on TV with curved or recessed back panel as shown in diagram 2-B.
If you mount the TV rails to a television with flat back, you will not need a plastic spacer as shown in diagram
2-C. Make sure these screws are right! Some TVs have shallow threaded inserts; so we have provided 4
extra washers if the provided screws are too long.
Hang the TV on the Wall Plate and Adjust - First hook the TV rails over the top of the wall plate○
a in
diagram 3-A. Then tighten the safety screws on the bottom of TV rails○
b in diagram 3-B. You can adjust
your TV down to 10 degrees at maximum: first loosen one knob, second loosen the other knob and then
adjust the TV whichever degree you want. Finally tighten the two knobs.
Probleemoplossing Equip 650201
Als je de handleiding al zorgvuldig hebt gelezen maar geen oplossing voor je probleem hebt gevonden, vraag dan andere gebruikers om hulp
Specificaties
| Kleur van het product: | Zwart |
| Gewicht: | 2000 g |
| Breedte: | 450 mm |
| Hoogte: | 270 mm |
| Gewicht verpakking: | 2500 g |
| Materiaal behuizing: | Staal |
| Montagewijze: | Muur |
| Afmetingen verpakking (BxDxH): | 496 x 226 x 60 mm |
| Geschikt voor schermmaten: | 23 - 37 " |
| Maximale gewichtscapaciteit: | 75 kg |
| Certificering: | RoHS |
| Montage interface compatibiliteit (min): | 400 x 200 mm |
| Montage interface compatibiliteit (max): | 400 x 200 mm |
| Bereik kantelhoek: | -10 - 0 ° |